How to Replace a Kia Sportage Replacement Key

For a number of Kia models the key comes with an integrated keyless entry system. The key is usually akin to an electronic remote and can be changed by a new one purchased from a Kia dealer or a locksmith.

Key fobs might stop working for several reasons, including batteries that are dead, worn buttons signals, signal interference, water damage and a faulty receiver module. Here are some suggestions to assist you in getting your Kia sportage replacement key to work again.

How to replace a remote key or smartkey

The battery in your Kia's intelligent key will eventually have to be replaced, regardless of whether it's a remote key or a push-to-start one, or a normal metal key that is not equipped with an electronic transponder. This is particularly true if your car displays a message telling you that the smart or remote keys aren't powered.

Luckily, this is a relatively simple process. To replace the battery of the keyfob remove your mechanical key from the slit at the back of the fob. Then, you need to pry the cover open. Inside the key fob, there will be a small screw that holds the battery in place. Using a small screwdriver, remove the screw and pull out the old battery. Install the new battery and close the opening on the key fob.

When the key fob is equipped with an updated battery Test it by pressing the locks and unlock buttons. You're good to go when the doors lock or unlock as you expect. You can now use the hands-free feature to lock and unlock your Kia when your fingers get chilly or when you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a programing machine that is only available to the locksmith for cars or dealer. Other keys (non-transponder metal keys) don't require programming. If your key requires to be programmed again, you must be aware of the key code that is stamped on the key code tag and record it in a secure location.

How do I replace the battery?

If your Kia key fob is not responding to pressing the lock or unlock button on the fob, this is a sign that the battery should be replaced. A low battery may also cause other issues like the check engine light flashing on or a delay in cranking the engine. Fortunately replacing the key fob battery is a simple DIY project that requires only a few basic tools.

Make sure you turn off your vehicle and close the doors before you begin. Find the small metal or plastic piece that is located at the bottom of the key fob. Then, jiggle it until the metal key comes out. Then, you can insert the key into the driver's door handle to open your car.

To replace the key fob battery, take off the cover from the back and use a plastic pry bar tool to release the latch holding the black negative battery cable. Remove the old battery and orient the new one in a way that the "+" positive side faces you, while the "-" negative side is facing the fob's metal electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.

After you have installed the new battery, turn the key fob off and on in the ignition until the door locks cycle. You can then test your Kia's key fob once more to ensure it's functioning properly.

how much does a kia key fob cost do you replace a keyless keys

You could have the standard keyfob or Smart Key, based on the model of Kia Sportage. The smart key has an embedded mechanical key blade unlike the standard key fob, which does not. Both key fobs come with a battery that will eventually require replacement. Fortunately, this is an easy process that only takes about two minutes.

Be sure to switch off your Kia and be on a flat well-lit and well-lit area before you begin. Remember that the fob has tiny parts that could be thrown off in the event of a mishap.

The first step is to locate the small release button that is located on the back of the lower part of the fob. This will either be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened and you are able to remove the old battery and replace it. The new battery is one called CR-2032 and can be purchased through the internet or at a local auto parts store. After you're done, your key fob should be able to lock and unlock your vehicle even if it's not running.

How to replace the mechanical key?

The Kia key fob is a wonderful feature that lets us lock and unlock our Car Lockout with the touch of one button. Like any other device it is possible that the Kia key fob may have issues. There are ways to resolve these issues and keep your key fobs in good working order for a long time.

A dead or low-quality battery is one of the most frequently encountered issues. This can cause the fob to cease working or work intermittently. If this happens then try replacing the battery with a new one.

If this doesn't solve the issue Try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be careful not damage any internal components, or scratch the plastic. Once the battery is removed, replace it with a new one.

Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to ensure that it's working properly. Contact a dealer locksmith to address the issue in the event that the fob is not working. Make sure they make you an emergency key that works in all the door and trunk cylinders to prevent lockouts in the future.