How to Replace a Kia Sportage Replacement Key

For a variety of Kia models, the key contains the keyless entry system that is built into the key. This key usually resembles an remote control, and can be replaced by a new one purchased from an Kia dealer or a locksmith.

Key fobs can fail to function due to a variety of reasons, including an inactive battery, worn out buttons, signal interference or water damage. Here are some suggestions on how you can get your Kia Sportage replacement key back to working.

How do you replace the remote key or smart key

The battery in your Kia's intelligent key will eventually require to be replaced, regardless of whether it's a remote, a push-to-start key or a standard metal key that doesn't have an electronic transponder. This is particularly when your car displays a message indicating that the smart key kia sportage or remote keys are not powered by batteries.

It's a simple process. To replace the keyfob battery take out your mechanical key from the slit on the back of the fob. Then, pull the cover off. Inside the key fob, there will be the small screw that holds the battery in place. By using a small screwdriver unscrew the screw and pull out the battery that was in place. Then insert the new one and close the slit in the key fob.

When the key fob is equipped with a fresh battery Test it by pressing the locks and unlock buttons. If the doors lock and unlock according to your expectations, then you're all set! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you have to run errands around Brandon.

Note: Certain keys may require to be programmed (transponder chips or smart keys). This requires a computer, which is only available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) do not require programming. If you need to reprogramme your key, you'll need note the key code number on the key code tag.

How do you replace the battery?

If the Kia key fob does not respond to pressing the lock or unlock button, it's likely that the battery is not fully charged. A low battery may cause other issues, like the check engine light appearing or the engine not turning correctly. It is relatively easy to replace the key fob batteries with only some tools.

Before you begin the process ensure that your vehicle is off and all doors are shut. Locate the small metal or plastic piece on the bottom of your key fob, and jiggle it until a metal key slips out. The key can be placed inside the driver door handle to unlock your car.

To replace the key fob's battery, remove the cover at the rear and use a plastic pry bar tool to release the latch that holds the black negative battery cable. Remove the old battery, and then orient the replacement battery so that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid breaking or bending the steel contacts.

After the new battery has been installed, turn the key fob off and on in the ignition until the door locks. Then you can test your Kia key fob to see whether it's functioning properly again.

How do you replace a keyless keys

You can have a standard keyfob or a Smart Key based on the model of kia rio Key Replacement Sportage. The smart key comes with an embedded mechanical key blade however, the standard key fob does not. Both key fobs contain an internal battery that will eventually need to be changed. This is a simple procedure that takes only two minutes.

Be sure to switch off your Kia and stand on a level and well-lit surface prior to you begin. Keep in mind that the fob contains small parts that can be thrown off when you're not careful.

The first step is to find the small release button that is located on the back of the lower part of the fob. It could be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been opened, take out the battery. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. Once you're done it should be possible to lock and unlock your vehicle using your key fob, even if the engine isn't running!

How do you replace the mechanical key

The Kia keyfob is a wonderful convenience that allows us to lock or unlock our car simply by pressing the button. Like all devices, the Kia key fob can have issues at times. Luckily, there are ways to troubleshoot these issues and ensure that our key fobs are in good working order for the long run.

A dead or drained battery is one of the most common problems. This can cause your device to stop working or work intermittently. If this is what you are experiencing you should replace the battery a new one.

If this doesn't solve the problem, try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not to damage any internal components, or scratch the plastic. Once the battery is opened, carefully remove the old battery and replace it with a new one.

Once the new battery is installed, close and unlock the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that will fit into the slot). Test the key fob to confirm it's working as intended. Contact a dealer or locksmith to solve the issue if the fob is still not working. Make sure they make you an emergency key that works in all the trunk and door cylinders in order to avoid lockouts again.